Tankless-Water-Heater

TANKLESS
WATER HEATERS
Models & Prices

Tankless Water Heater Product Guide
Description / Specification

Tankless Water Heater Applications
Residential / Commercial

Tankless Water Heater Electrical Guide
Service Calculations

Tankless Water Heater Installation
Plumbing / Electrical

Tankless Water Heater Cost Comparisons
Reports / Listings

Tankless Water Heaters Service Guide
Remove / Repair

SEND TO A FRIEND

ELECTRICAL Tankless Water Heater Installation GUIDE
CONNECTION TO POWER SUPPLY

WARNING
CANADIAN CIRCUIT PROTECTION DISCLAIMER

ALL WIRING AND CIRCUIT PROTECTION SHOWN
ON THIS WEBSITE ARE SIZED ACCORDING TO THE U.S.
NATIONAL ELECTRIC CODE (NEC).

IN CANADA, WIRING AND CIRCUIT PROTECTION MUST BE SIZED
ACCORDING TO THE CANADIAN ELECTRIC CODE (CEC).
THE CANADIAN ELECTRIC CODE REQUIRES THAT ALL
SUPPLY WIRES AND CORRESPONDING CIRCUIT
PROTECTION FOR POTABLE WATER HEATERS AND
HYDRONIC SPACE HEATERS BE SIZED TO A MINIMUM
125% OF THE MAXIMUM CURRENT RATING OF THE HEATER.

Tankless Water Heater Installation and service must be by qualified personnel only!

NOTE: This unit must be installed to meet the current National Electric Code, and any applicable local plumbing, electrical, heating and air conditioning codes.

Install wiring from the unit to the Main Power Circuit Breaker Panel. Connect the wiring to the unit as shown on the wiring diagram attached to the inside of the unit's cover. SEE WIRING DIAGRAMS (RA-28) (RA-22 & RA-18) (RA-14 & RA-11)

WARNING

MODELS RA-14 THROUGH RA-28 REQUIRE MULTIPLE POWER SOURCES. WHEN WIRED DIRECTLY TO THE BREAKER BOX, THEY REQUIRE MORE THAN ONE DOUBLE POLE CIRCUIT BREAKER.

RISK OF ELECTRICAL SHOCK. HEATING ELEMENT IS NOT GROUNDED. SOME UNITS HAVE MULTIPLE POWER SUPPLIES. DISCONNECT ALL POWER SUPPLIES BEFORE SERVICING.

IF USING STRANDED WIRE, MAKE SURE THAT ALL STRANDS ARE IN SECURE PLACEMENT IN THE TERMINAL BLOCK. A LOOSE STRAND IN CONTACT WITH THE CIRCUIT BOARD CAN IMPAIR PERFORMANCE OR DAMAGE THE BOARD.

BACK TO TOP?

HEATER SUPPLY SIDE CONNECTION

FOR MODELS RA-9 THROUGH RA-l1, ONE PAIR OF WIRES SHOULD BE ATTACHED WITHIN THE UNIT AT POWER CIRCUIT 1 (CKT 1)-ONE WIRE TO L1 AND ONE WIRE TO L2. FOR MODELS RA-14 THROUGH RA-22, A SECOND PAIR OF WIRES MUST ALSO BE ATTACHED AT POWER CIRCUIT 2 (CKT2)-ONE TO Ll AND ONE TO L2. FOR MODEL
RA-28, A THIRD AND FOURTH PAIR OF WIRES ARE REQUIRED FOR POWER CIRCUITS 3 AND 4 (CKT 3 & CKT 4).

MAIN POWER CIRCUIT BREAKER DIAGRAM

WHERE REQUIRED BY CODE, USE A DISCONNECT SWITCH ADJACENT TO THE HEATER. WHEN MAKING THIS TYPE OF Tankless Water Heater Installation, BE SURE THE MAIN FEEDER WIRES USED ARE PROPERLY SIZED.

Install the proper size circuit breaker (see Product Specifications). Be sure that the unit-to-power supply circuits are properly connected. For model RA-9 - RA-1l, the pair of feeders attached to power circuit 1 (CKT 1) should be attached to one 2-pole breaker, and for models RA-14 - RA-22, the second pair attached to power circuit 2 (CKT 2) should be attached to a second 2-pole breaker such that the total load will be balanced. For model RA-28, two additional breakers are required for power circuits 3 and 4 (CKT 3 & 4).

BACK TO TOP?

PRE-POWER CHECK

1. After all electrical connections have been made, every effort should be made to verify a safe Tankless Water Heater Installation. Again check to be sure all connections in the unit disconnect and/or circuit breaker panel are secure. Check to be sure that an adequate ground has been properly connected. Check to be sure that adequate size breakers have been installed properly. Remember that breakers that are too large are more dangerous than breakers that are too small.

2. RUN WATER THROUGH THE UNIT UNTIL AIR IS PURGED.

POWER CHECK

Check only after the Pre-Power Check has been completed and the unit filled with water. Turn on the Main Power Circuit Breakers. Verify that the heater’s GREEN POWER-ON indicator light is illuminated.

USE EXTREME CAUTION WHEN CHECKING VOLTAGE TO THE UNIT.

Check the voltage available to each active power circuit. SEISCO models RA-9 to RA-28 are designed to operate from a 208V to 240V power supply. Connect a voltmeter at power circuit 1 (CKT 1) between L1 and L2. (For models with multiple power circuits utilized, continue to check voltage at each additional power circuit.)

OPERATIONAL CHECKS

Turn water on MEDIUM-LOW utilizing any sink allowing water to run for a couple of minutes to ensure that all air is purged from the unit. You will hear a "click" as the relays on the circuit board engage. It is normal to hear a "hissing" or "crackling" noise from the heat exchanger after the unit is started. With the unit's cover removed, verify with an ammeter that there is ELECTRICAL CURRENT through each heating element circuit. DISREGARD THE WATER TEMPERATURE WHILE DOING THIS TEST.

TURN OFF FAUCETS AFTER COMPLETING OPERATIONAL CHECK

Thermostat settings are factory preset for units employing a circuit board potentiometer (thermostat).

THIS Tankless Water Heater Installation MUST BE DONE BY QUALIFIED AND LICENSED CONTRACTORS. Refer to your local electrical and plumbing codes for additional information.

BACK TO TOP?

Home || Tankless Company Introduction || Tankless Patent Information || Tankless Distribution || Contact Us & LINKS ||
Tankless Product Information || Tankless Application || Tankless Tankless Water Heater Installation || Trouble Shooting || Buy On Line